Rua Nicolau Monteiro 137, Sala 101 - Vargem Alta - ES
Meets NR12, category 2;
Cutting disc: 350 mm to 500 mm in diameter with 1 ”shaft hole;
Through-cut capacity: height of up to 150 mm in one operation and 300 mm in two operations;
Tilting cutting system with manual height adjustment that allows uncut cuts up to a height of 300 mm between the cutting table and the blade (450 E 500 mm);
Worktable: 100 kg capacity, free measurements of 650 mm x 400 mm, inclination of -45 ° and + 45 ° with lock at 0 ° and adjustable and removable side support arm of 300 mm;
Table stop for angular cutting with adjustment of +30 º / - 30º;
Total installed power 6.0 KW;
Main motor with 7.5 CV - 3F 220/380/440 V magnetic brake - 2 poles. (IP55);
Machine dimensions: Comp. 2,670 mm x Width 1085 mm x Alt. 2,000 mm;
Total weight: 890 kg.
NCM: 8464.10.00;
Equipment prepared for wet cutting (optional dry cutting);
Laser cut alignment system (red);
Cutting system by manual command, moving the cutting car through a handle, with a very light traction load for the operator;
Standard machine elements (ISO / DIN);
Equipment built in tubes and sheets made of SAE 1020/1045 steel and nodular cast iron;
Disc cooling system by concentrated water jets, type Fixoflex with automatic or manual activation;
Bilateral sealing system of the bearing with double seals and water deflector on the disc side;
Equipment freely supported on a regular floor and prepared for lifting by bridges and winches;
Electrical panel (NR10-IP54) with 220/380/440 V supply voltage and 24VAC control voltage, emergency button with key / safety lock on the control panel and electrical panel protection box with safety door, with digital meters and analog hour meter;
Access door to the cutting table equipped with anti-cheat key model AZ, which instantly activates the magnetic brake of the cutting engine as soon as it is activated, stopping it completely in approximately 2 seconds;
Antioxidant paint based on Epoxy Bi-component with high resistance to humidity and aggressive environments;
Coif for dust collection system, on the table and on the disk protection, with quick aluminum couplings, for residual dust collector hoses. (Vacuum cleaner is not included);
System for capturing wet waste per box / decantation tank and recirculation by submerged pump 220V;
This equipment does not accompany production inputs, such as diamond tools.
Operation / maintenance manual;
Supply of 4 (four) Magnetic Bases for fixing the refractory / block.
Coif for dust collection system, on the table and on the disk protection, with quick aluminum couplings, for residual dust collector hoses. (Vacuum cleaner is not included).
In order to provide greater safety to users and machine operators, some preventive measures and the installation of new safety devices have been implemented, as described below. Two mushroom emergency keys with double contact will be installed at the ends of the machine in order to guarantee its total shutdown by its operator or any close person trained with greater agility and speed, in case of any incident or abnormality in the operation of the machine.
The mobile protection grids will be supervised by magnetic keys, double contact, which will detect any movement of the same, in case of an attempt to open during the cutting operation and will cause the security system to cease all operation immediately. Any and all interventions that are made on the machine, whether by activating a safety sensor or "knocking" the machine's emergencies, will cause the entire machine to enter emergency mode and stop its full operation immediately. It will only be released again when the faults are verified, "reset" and given a new start command in the process.
All safety mechanisms (magnetic keys and emergency buttons) will be monitored individually by dedicated safety relays, which are available at all times.
Monitoring each safety device and itself, that is, if there is an internal failure in the relay, whether due to bad contact, the presence of dust, or eventual damage to the device, it goes into error and generates a failure in the system, blocking its operation. All safety devices will remain active even in manual mode. The entire process of the machine, automatic or manual, is assembled in order to ensure that its operators do not have the need to be in direct contact with the risk areas of the machine, it will only be necessary for the operator to feed the machine with the part to be cut, and give a START command so that the process starts and ends automatically.